Viking-pump TSM610: Offset Gear Reducers User Manual download pdf

SECTION TSM

PAGE

ISSUE

CONTENTS

Introduction .........................................................................1

Special Information .............................................................2

Lubrication .......................................................................... 2

Installation ..........................................................................3

Operation ............................................................................3

Disassembly .......................................................................3

Assembly

“A” Reducer ......................................................................4

“B” Reducer ......................................................................5

“C” Reducer ......................................................................6

Technical Data .................................................................... 7

Warranty .............................................................................8

INTRODUCTION

The illustrations used in this manual are for identification

purposes only and cannot be used for ordering parts. Obtain

a parts list from the factory or a Viking® representative.

Always give the complete name of the repair part and part

number along with the reducer part number when ordering

repair parts. The reducer part number is stamped on the

nameplate.

UNMOUNTED PUMP AND UNIT MODEL NUMBERS

FIGURE 1

“A” SIZE HELICAL GEAR REDUCER

610

“A”, “B” AND “C” SIZE REDUCERS

SIZE PART NUMBER RATIO

3-551-049-224 2.24:1

3-551-050-276 2.76:1

3-551-051-343 3.43:1

3-551-052-417 4.17:1

3-551-054-187 1.87:1

3-551-055-224 2.24:1

3-551-001-276 2.76:1

3-551-002-340 3.40:1

3-551-003-419 4.19:1

3-551-004-506 5.06:1

3-551-005-627 6.27:1

3-551-007-765 7.65:1

3-551-056-221 2.21:1

3-551-032-280 2.80:1

3-551-008-331 3.31:1

3-551-009-421 4.21:1

3-551-010-508 5.08:1

3-551-011-624 6.24:1

3-551-012-795 7.95:1

FIGURE 2

“B” SIZE HELICAL GEAR REDUCER

FIGURE 3

“C” SIZE HELICAL GEAR REDUCER

Electronic copies of the most current TSM issue can be found on the Viking Pump website at www.vikingpump.com

VIKING PUMP, INC. • A Unit of IDEX Corporation • Cedar Falls, IA 50613 USAVIKING PUMP, INC. • A Unit of IDEX Corporation • Cedar Falls, IA 50613 USA

TECHNICAL SERVICE MANUAL

VIKING

HELICAL GEAR REDUCERS

“A”, “B”, AND “C” SIZES

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - TECHNICAL SERVICE MANUAL

SECTION TSMPAGEISSUECONTENTSIntroduction ...1Special Information ...

Page 2 - LUBRICATION

FIGURE 4TYPICAL INSTALLATIONNOTE: UNIT FURNISHED WITH COUPLING GUARDS AS STANDARDSECTION TSM 610 ISSUE G PAGE 2 OF 8DANGER !Before opening any Viki

Page 3 - OPERATION

SECTION TSM 610 ISSUE G PAGE 3 OF 8INSTALLATIONViking helical gear reducers are shipped completely assembled and ready for installation except for

Page 4 - ASSEMBLY

1. Install ball bearings on the pinion shaft. Be sure the single row bearings are seated firmly against the shoulders on the pinion shaft.2.

Page 5

SECTION TSM 610 ISSUE G PAGE 5 OF 8ASSEMBLY“B” Reducer Assembly - See Fig. 8ITEM NAME OF PART ITEM NAME OF PART ITEM NAME OF PART1 Drain Plug 11 Ba

Page 6

ITEM NAME OF PART ITEM NAME OF PART ITEM NAME OF PART1 Drain Plug 7 Gasket 14 Gear Shaft2 Breather 9 Ball Bearing (Double Row) 15 Ball Bearing (Double

Page 7 - Service Factor Table

SECTION TSM 610 ISSUE G PAGE 7 OF 81. Determine ratio to obtain desired output speed.2. Determine actual horsepower requirements of application.

Page 8

Comments to this Manuals

No comments

Viking-pump TSM610: Offset Gear Reducers User Manual

Browse online or download User Manual for Pumps Viking-pump TSM610: Offset Gear Reducers. Viking Pump TSM610: Offset Gear Reducers User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Pumps Viking-pump TSM610: Offset Gear Reducers